TC7PA17FU 2014-03-01 1 marking pin assignment (top view) toshiba cmos digital integrat ed ci rcuit silicon monolithic TC7PA17FU dual schmitt buffer features ? operating voltage range: v cc = 1.8 to 3.6 v ? high-speed operation: t pd = 4.0 ns (max) at v cc = 3.0 to 3.6 v t pd = 4.3 ns (max) at v cc = 2.3 to 2.7 v t pd = 8.6 ns (max) at v cc = 1.8 v ? high-level output current: i oh /i ol = 24 ma (min) at v cc = 3.0 v i oh /i ol = 18 ma (min) at v cc = 2.3 v i oh /i ol = 6 ma (min) at v cc = 1.8 v ? 3.6-v tolerant inputs. ? 3.6-v power down protection outputs absolute maximum ratings (ta = 25c) note: using continuously under heavy loads (e.g. the application of high temperatur e/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operati ng temperature/current/voltage, etc. ) are within the absolute maximum ratings and the operating ranges. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and indi vidual reliability data (i.e. reliability test report and estimated failure rate, etc). note 1: v cc = 0 v note 2: high or low state. i out absolute maximum rating must be observed. note 3: v out < gnd (us6) weight: 0.0068 g (typ.) characteristics symbol rating unit supply voltage v cc ? 0.5 to 4.6 v dc input voltage v in ? 0.5 to 4.6 v ? 0.5 to 4.6 (note 1) dc output voltage v out ? 0.5 to v cc + 0.5 (note 2) v input diode current i ik ? 50 ma output diode current i ok ? 50 (note 3) ma dc output current i out 50 ma power dissipation p d 200 mw dc v cc /ground current i cc 100 ma storage temperature t stg ? 65 to 150 c product name e a l gnd 2 6 1y 5 v cc 4 2y 1a 1 2a 3 start of commercial production 2002-12
TC7PA17FU 2014-03-01 2 iec logic symbol truth table operating ranges characteristics symbol rating unit 1.8 to 3.6 supply voltage v cc 1.2 to 3.6 (note 4) v input voltage v in ?0.3 to 3.6 v 0 to 3.6 (note 5) output voltage v out 0 to v cc (note 6) v 24 (note 7) 18 (note 8) output current i oh /i ol 6 (note 9) ma operating temperature t opr ? 40 to 85 c note 4: data retention only note 5: v cc = 0 v note 6: high or low state note 7: v cc = 3.0 to 3.6 v note 8: v cc = 2.3 to 2.7 v note 9: v cc = 1.8 v a y l l h h in a out y
TC7PA17FU 2014-03-01 3 electrical characteristics dc characteristics (2.7 v < v cc 3.6 v) dc characteristics (2.3 v v cc 2.7 v) ta = 40 to 85 c characteristics symbol test condition v cc (v) min max unit 3.6 ? 2.2 high level v p ? 3.0 ? 2.0 v 3.6 0.8 ? threshold voltage low level v n ? 3.0 0.7 ? v 3.6 0.3 1.2 hysteresis voltage v h ? 3.0 0.3 1.2 v i oh = ?100 a 2.7 to 3.6 v cc ? 0.2 ? i oh = ? 12 ma 2.7 2.2 ? i oh = ? 18 ma 3.0 2.4 ? high level v oh v in = v ih i oh = ? 24 ma 3.0 2.2 ? i ol = 100 a 2.7 to 3.6 ? 0.2 i ol = 12 ma 2.7 ? 0.4 i ol = 18 ma 3.0 ? 0.4 output voltage low level v ol v in = v il i ol = 24 ma 3.0 ? 0.55 v input leakage current i in v in = 0 to 3.6 v 2.7 to 3.6 ? 5.0 a power-off leakage current i off v in , v out = 0 to 3.6 v 0 ? 10.0 a v in = v cc or gnd 2.7 to 3.6 ? 20.0 quiescent supply current i cc v cc (v in , v out ) 3.6 v 2.7 to 3.6 ? 20.0 increase in i cc per input i cc v ih = v cc ? 0.6 v 2.7 to 3.6 ? 750 a ta = 40 to 85 c characteristics symbol test condition v cc (v) min max unit high level v p ? 2.3 ? 1.8 threshold voltage low level v n ? 2.3 0.5 ? v hysteresis voltage v h ? 2.3 0.3 1.0 v i oh = ?100 a 2.3 to 2.7 v cc ? 0.2 ? i oh = ? 6 ma 2.3 2.0 ? i oh = ? 12 ma 2.3 1.8 ? high level v oh v in = v ih i oh = ? 18 ma 2.3 1.7 ? i ol = 100 a 2.3 to 2.7 ? 0.2 i ol = 12 ma 2.3 ? 0.4 output voltage low level v ol v in = v il i ol = 18 ma 2.3 ? 0.6 v input leakage current i in v in = 0 to 3.6 v 2.3 to 2.7 ? 5.0 a power-off leakage current i off v in , v out = 0 to 3.6 v 0 ? 10.0 a v in = v cc or gnd 2.3 to 2.7 ? 20.0 quiescent supply current i cc v cc (v in , v out ) 3.6 v 2.3 to 2.7 ? 20.0 a
TC7PA17FU 2014-03-01 4 dc characteristics (1.8 v v cc < 2.3 v) ac characteristics (input t r = t f = 2.0 ns, c l = 30 pf, r l = 500 ) ta = 40 to 85 c characteristics symbol test condition v cc (v) min max unit 1.8 1.0 8.6 2.5 0.2 0.8 4.3 propagation delay time t plh t phl (figure 1 and 2) 3.3 0.3 0.6 4.0 ns for c l = 50 pf, add approximately 300 ps to the ac maximum specification. ta = 40 to 85 c characteristics symbol test condition v cc (v) min max unit high level v p ? 1.8 ? 1.4 threshold voltage low level v n ? 1.8 0.25 ? v hysteresis voltage v h ? 1.8 0.2 0.95 v i oh = ?100 a 1.8 v cc ? 0.2 ? high level v oh v in = v ih i oh = ? 6 ma 1.8 1.4 ? i ol = 100 a 1.8 ? 0.2 output voltage low level v ol v in = v il i ol = 6 ma 1.8 ? 0.3 v input leakage current i in v in = 0 to 3.6 v 1.8 ? 5.0 a power-off leakage current i off v in , v out = 0 to 3.6 v 0 ? 10.0 a v in = v cc or gnd 1.8 ? 20.0 quiescent supply current i cc v cc (v in , v out ) 3.6 v 1.8 ? 20.0 a
TC7PA17FU 2014-03-01 5 dynamic switching characteristics (input t r = t f = 2.0 ns, c l = 30 pf) ta = 25 c characteristics symbol test condition v cc (v) typ unit v in = 1.8 v, v il = 0 v (note 10) 1.8 0.25 v in = 2.5 v, v il = 0 v (note 10) 2.5 0.6 quiet output maximum dynamic v ol v olp v in = 3.3 v, v il = 0 v (note 10) 3.3 0.8 ns v in = 1.8 v, v il = 0 v (note 10) 1.8 ?0.25 v in = 2.5 v, v il = 0 v (note 10) 2.5 ?0.6 quiet output minimum dynamic v ol v olv v in = 3.3 v, v il = 0 v (note 10) 3.3 ?0.8 ns v in = 1.8 v, v il = 0 v (note 10) 1.8 1.5 v in = 2.5 v, v il = 0 v (note 10) 2.5 1.9 quiet output minimum dynamic v oh v olp v in = 3.3 v, v il = 0 v (note 10) 3.3 2.2 ns note 10: characteristics guaranteed by design. capacitive characteristics ta = 25 c characteristics symbol test condition v cc (v) typ unit input capacitance c in ? 1.8, 2.5, 3.3 4 pf power dissipation capacitance c pd f in = 10 mhz (note 11) 1.8, 2.5, 3.3 27 pf note 11: c pd is defined as the value of the internal equivalent capacitance which is calc ulated from the operating current consumption without load. average operating current can be obtained by the equation: i cc (opr.) = c pd ?v cc ?f in + i cc /2
TC7PA17FU 2014-03-01 6 ac test circuit figure 1 ac waveforms figure 2 t plh , t phl output measure c l = 30 pf r l = 500 r l c l 90% 10% output input v ol v oh v ih v m t plh t phl 2.0 ns 2.0 ns t r t f v cc symbol 3.3 0.3 v 2.5 0.2 v 1.8 v v ih 2.7 v v cc v cc v m 1.5 v v cc /2 v cc /2 v m
TC7PA17FU 2014-03-01 7 package dimensions weight: 0.0068 g (typ.)
TC7PA17FU 2014-03-01 8 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively "toshiba"), reserve the right to make changes to the in formation in this document, and related hardware, software and systems (collectively "product") without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba's written permission, reproduc tion is permissible only if reproduction is without alteration/omission. ? though toshiba works continually to improve product's quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before customers use the product, create designs including the product, or incorporate the product into their own applications, cu stomers must also refer to and comply with (a) the latest versions of all relevant toshiba information, including without limitation, this document, the specifications, the data sheets and application notes for product and the precautions and condi tions set forth in the "toshiba semiconductor reliability handbook" and (b) the instructions for the application with which the product will be us ed with or for. customers are solely responsible for all aspe cts of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this product in such design or applications; (b) eval uating and determining the applicability of any info rmation contained in this document, or in c harts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operatin g parameters for such designs and applications. toshiba assumes no liability for customers' product design or applications. ? product is neither intended nor warranted fo r use in equipments or systems that require extraordinarily high levels of quality and/or reliability, and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage and/or serious public impact ( " unintended use " ). except for specific appl ications as expressly stated in this document, unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used f or automobiles, trains, ships and other transportation, traffic si gnaling equipment, equipment used to control combustions or expl osions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. if you use product for unintended use, toshiba assumes no liability for product. for details, please contact your toshiba sales representative. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ? absent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability wh atsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the applicable export laws and regulations including, without limitat ion, the japanese foreign exchange and foreign trade law and t he u.s. export administration regulations. export and re-export of pr oduct or related software or technology are strictly prohibit ed except in compliance with all appl icable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations.
|
